By Lisa Williamson
Your audio system will not be in a position to give out admirable sound if the amplification mechanism is faulty. An amp plays a very vital role in a given sound system where it raises an electrical signal to a level suitable for an output device such as a speaker or headsets. If you detect that your speaker is giving out a weaker sound than expected, then you are supposed to have the amp checked. Another situation where amplifier repair will be needed is when the output generated is distorted or not clear.
Normally, it is easy to troubleshoot amplification systems since most of them are constructed in a way that you can view all internal components and identify the faulty one. A number of steps are followed in accomplishing repair of an audio system. The first thing is to unplug the device from the wall and place it on a spacious table.
Normally, it is easy to troubleshoot amplification systems since most of them are constructed in a way that you can view all internal components and identify the faulty one. A number of steps are followed in accomplishing repair of an audio system. The first thing is to unplug the device from the wall and place it on a spacious table.
A screwdriver is applied in loosening the side and top covers of the appliance. Once all components are visible, technicians normally look if there are components which are burned before they embark on sophisticated troubleshooting procedures. If the system had just failed, an odor will suggest that there is a burned component like a resistor or a transistor.
All power transistors in the system can be identified by use of the service manual obtained from the manufacturer. The power button is put on and a multimeter applied in determining if there is voltage on the pins of these transistors. The rest of the power ICs need to be identified and the same test done on them. The fuse will be tested for continuity and if found to be blown, replacement with a suitable one will be done.
Once the power supply is tested and found to be working, troubleshooting proceeds to the next stage. This involves finding out whether there is any component in the other sections that is faulty. A freezer is used to spray the components, one after another, with a short burst. The system is then put on and the component that is last frozen before the device begins to function is the faulty one.
A faulty element is removed using heat from a gun to melt the solder holding it in place. A needle nose pliers is the suitable tool to apply in puling the pins out of the board. Remove the screws holding the board in position so that you gain access of all sides. Cleaning of the holes left on the board is done through utilizing a solder wick.
The technician uses the manual to identify the component so that he replaces it with its equivalent. The position as well as orientation of the element should be maintained and the pins should always be straight. A side cutter is supposed to be used in trimming the excess pins once the solder h
All power transistors in the system can be identified by use of the service manual obtained from the manufacturer. The power button is put on and a multimeter applied in determining if there is voltage on the pins of these transistors. The rest of the power ICs need to be identified and the same test done on them. The fuse will be tested for continuity and if found to be blown, replacement with a suitable one will be done.
Once the power supply is tested and found to be working, troubleshooting proceeds to the next stage. This involves finding out whether there is any component in the other sections that is faulty. A freezer is used to spray the components, one after another, with a short burst. The system is then put on and the component that is last frozen before the device begins to function is the faulty one.
A faulty element is removed using heat from a gun to melt the solder holding it in place. A needle nose pliers is the suitable tool to apply in puling the pins out of the board. Remove the screws holding the board in position so that you gain access of all sides. Cleaning of the holes left on the board is done through utilizing a solder wick.
The technician uses the manual to identify the component so that he replaces it with its equivalent. The position as well as orientation of the element should be maintained and the pins should always be straight. A side cutter is supposed to be used in trimming the excess pins once the solder h
Once the power supply is tested and found to be working, troubleshooting proceeds to the next stage. This involves finding out whether there is any component in the other sections that is faulty. A freezer is used to spray the components, one after another, with a short burst. The system is then put on and the component that is last frozen before the device begins to function is the faulty one.
A faulty element is removed using heat from a gun to melt the solder holding it in place. A needle nose pliers is the suitable tool to apply in puling the pins out of the board. Remove the screws holding the board in position so that you gain access of all sides. Cleaning of the holes left on the board is done through utilizing a solder wick.
The technician uses the manual to identify the component so that he replaces it with its equivalent. The position as well as orientation of the element should be maintained and the pins should always be straight. A side cutter is supposed to be used in trimming the excess pins once the solder has been applied.
Once replacing a spoiled component is finished, the board is fastened back to its position. The device is then plugged in and the power turned on. If the system is confirmed to be working as required, the power is put off and the covers replaced.
About the Author:
A faulty element is removed using heat from a gun to melt the solder holding it in place. A needle nose pliers is the suitable tool to apply in puling the pins out of the board. Remove the screws holding the board in position so that you gain access of all sides. Cleaning of the holes left on the board is done through utilizing a solder wick.
The technician uses the manual to identify the component so that he replaces it with its equivalent. The position as well as orientation of the element should be maintained and the pins should always be straight. A side cutter is supposed to be used in trimming the excess pins once the solder has been applied.
Once replacing a spoiled component is finished, the board is fastened back to its position. The device is then plugged in and the power turned on. If the system is confirmed to be working as required, the power is put off and the covers replaced.
About the Author:
You can visit www.musictechnology.com for more helpful information about All You Need To Know Pertaining Amplifier Repair.